Fire Extinguisher and Agents
Portable Fire Extinguisher
Wheeled Fire Extinguisher
Automatic Fire Extinguisher
Simple Fire Extinguishing Tool
Package Type Automatic Fire Extinguishing System
Fire & Gas Detection, Signaling and Other Electrical Equipment
Gas Leakage detector
Manual Call Point
Control Panel & Transmitter
Hydraulic Equipment & Others
Flexible Sprinkler Hose With Fittings
Angle Valve & Hydrant
Water Flow Detecting Device
Gas Selection Valve
Fire Department Connector
Descending Life line
Flame Retardant Products
Flame Retardant Agents
Fire Fighting Clothes, Glove, Boots
Heat Proximity Clothing
Heavy Rescue Vehicle
Water and Foam Carrying Apparatus
Demolition Fire Apparatus
94 page : (1/10)
Dry riser inlet valves
Dry riser inlet valves are used to supply water connecting to firefighting equipm ent or sprinkler systems and installed at the place having an easy access for fir e trucks and the exposed place where fire can be suppressed without obstacle s. There are two types of inlet valves; exposed(E type) and inside(C and F typ e).
Deluge valves open to admit water through the main line when the pneumatic s upply pressure is removed or the solenoid valve is activated. Shingyoung Delug e valve is furnished fully factory-assembled and ready for installation at the app ropriate point in the system. Shinyoung deluge valve is a hydraulically operated valve, it requires a minimum line pressure of approximately 5 psig in order to fu nction. The valve functions on a simple principle of pressure differential. The lin e pressure at the inlet of the valve is bypassed through the pilot control piping t o the diaphragm chamber of the valve. The pressure works against the pressur e under the valve seat. Because the effective area of the diaphragm is greater t han that of the clapper, the valve is held tightly closed. As the solenoid valve all ows the pressure to bleed off the diaphragm chamber, the two opposing pressu res begin to balance and the valve will begin to open.
The alarm valves of Shinyoung are optimized and essentially used for the wet sprinkler system. The y detect the flow of water and alert a fire alarm when there is a fire. The alarm valves of Shinyoung are carefully examined by KFI(Korea Fire Institute) undertaking strict internal pressure tests, functio nal examinations and visual inspections. The alarm valve is consisted of an alarm switch, pressure g auges, a clapper, and other pipes. In the state of the fire water line(fire pump- protection system)of an alarm valve is filled with wate r, the clapper operates once fire occurs. The alarm switch sends signals to the fire alarm control pan el once a setting time of delay circuit passes, and an alarm alert goes off.
Descending Life Line
- Strength of Belt and Rope: 900 ~ 1,000kg - Maximum Service Load: 150kg - Maximum Number of Users: 1 person - Descending Speed : 16cm/s ~ 150cm/s - Flexible and untwisted cotton yarn-covered special air cable.
Pre-action fire sprinkler system in that water is not normally contained within the pipes. Pre-action sprinkler systems restain water with an electrically operated valve, known as a pre-action valve.
Wet type alarm valve
Alarm valve is magnet sensing clapper check valve with flanged & grooved type design, which ensures positive water flow for alarm operation and is designed for vertical installation in wet pipe sprinkler system.
These specifications apply to an alternative to fire extinguishers and indoor fire hydrant systems in regular offices, libraries, cultural properties, computer rooms, transformer vaults, exhibition halls, museums, semiconductor manufacturing facilities, chemical plants, and other places. *Wall Cabinet - Stainless Steel Body (Order Made) *One- fog™ Gun - 5Pattern, 100bar, 30 ℓ/min, *High Pressure Ball Valve - On- off Switch Type, SUS316-5/8” *High Pressure-Hosereel - Steel, Electrostatic Power Coating - Hose length : 30m or 50m - Hose
One-fog™ Water Mist Fixed System
-Minimized the water damage & water consumption. -Applicable in different fire types of A, B and C -Compact & easy to use -System can install independently in anywhere. -Highly efficient fire fighting -Smoke removal & Cooling effect -Help the escape from the fire zone -Protection for fire spread & radiant heat -Small droplets isolate the infer red, adsorb the heat -Non-toxic for environment & human
Mobile Pump System
Features - High reliability & momentary operation - Max. output rates of Pump : 30~42 ℓ/min - Max. pressure of Pump : 150 bar - Compact design and an user-friendly operation panel - Hose length : 50m / 100m - Hose pressure : 230 bar - Hose materials : Polyurethane, textile covered. - One fog Gun : Consists of 16 water mist nozzles+ 1 Jet spay nozzle Applications - Applicable in A, B and C class fire. - Operation method changes per each fire size and extinguishing condition. - Easy to use in a confined space with no need for large amount of water. - Lightweight, strong and high-pressure ho
The One-fog Gun has a rotor that enables users to select flow path and thus right discharge type, angle, rate and reach for the type, pattern, and size of the fire they attack. - Type : High-pressure water mist fire-extinguishing gun - Model : GSG-PS5, GSG-PV5 - Discharge Angle : 180˚ Protection - Body Length : 495mm, 490mm - Types of Discharge : 5 Spray Pattern - Weight : 3.6 kg, 3.8 kg - Fire Class : A, B, C - Working Pressure : 80 ~ 120 bar - Discharge Rate : 9~30 lpm - Material for Body : Duralumin and SUS 304 - Accessories (Optional) : Piercing Nozzle (Part No.: GSG-NR01): * SUS 304, 1KG, Quick Type. * Detachable straight stream nozzles and piercing nozzles maximize adaptability to the environment a
Copyright(c)2012 Korea Fire Institute All rights reserved.